Supermicro 6016GT-TF User Manual Page 15
- Page / 106
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
Chapter 2: Server Installation
2-1
Chapter 2
Server Installation
2-1 Overview
This chapter provides a quick setup checklist to get your SuperServer up and
running. Following these steps in the order given should enable you to have the
system operational within a minimum amount of time. This quick setup assumes
that your system has come to you with the processors and memory preinstalled. If
your system is not already fully integrated with a serverboard, processors, system
memory etc., please turn to the chapter or section noted in each step for details on
installing specifi c components.
2-2 Unpacking the System
You should inspect the box the system was shipped in and note if it was damaged
in any way. If the server itself shows damage you should fi le a damage claim with
the carrier who delivered it.
Decide on a suitable location for the rack unit that will hold the server. It should
be situated in a clean, dust-free area that is well ventilated. Avoid areas where
heat, electrical noise and electromagnetic fi elds are generated. You will also need
it placed near a grounded power outlet. Read the Rack and Server Precautions in
the next section.
2-3 Preparing for Setup
The box the server was shipped in should include two sets of rail assemblies, two
rail mounting brackets and the mounting screws you will need to install the system
into the rack. Follow the steps in the order given to complete the installation process
in a minimum amount of time. Please read this section in its entirety before you
begin the installation procedure outlined in the sections that follow.
Choosing a Setup Location
Leave enough clearance in front of the rack to enable you to open the front door •
completely (~25 inches) and approximately 30 inches of clearance in the back
of the rack to allow for suffi cient airfl ow and ease in servicing.This product is for
installation only in a Restricted Access Location (dedicated equipment rooms,
service closets and the like).
- SUPER 1
- Manual Revision 1.0a 2
- Release Date: May 27, 2010 2
- About This Manual 3
- Manual Organization 3
- Table of Contents 6
- Chapter 3 System Interface 7
- Chapter 4 System Safety 7
- Chapter 1 9
- Introduction 9
- 1-2 Serverboard Features 10
- 1-3 Server Chassis Features 11
- 1-4 GPU Subsystem 12
- System Block Diagram 13
- Chapter 1: Introduction 13
- 1-5 Contacting Supermicro 14
- Chapter 2 15
- Server Installation 15
- Warnings and Precautions! 16
- Rack Mounting Considerations 17
- Assembling the Outer Rails 20
- Chapter 3 27
- System Interface 27
- 3-3 Control Panel LEDs 28
- 3-4 SATA Drive Carrier LEDs 29
- Chapter 4 31
- System Safety 31
- 4-3 ESD Precautions 33
- LITHIUM BATTERY 34
- BATTERY HOLDER 34
- Chapter 5 35
- Advanced Serverboard Setup 35
- 5-2 Serverboard Installation 36
- 5-3 Connecting Cables 37
- 5-4 I/O Ports 38
- Socket Clip Load Plate 39
- Plastic Cap 39
- CPU Socket 40
- Load Plate 40
- Installing a CPU Heatsink 41
- 5-6 Installing Memory 42
- DIMM Population Table 43
- 5-6 Adding PCI Add-On Cards 44
- 5-7 Serverboard Details 45
- X8DTG-DF Quick Reference 46
- 5-8 Connector Defi nitions 47
- 5-9 Jumper Settings 53
- 5-10 Onboard Indicators 55
- 5-11 SATA Ports 56
- 5-12 Installing Software 57
- Supero Doctor III 58
- Chapter 6 61
- Advanced Chassis Setup 61
- 6-2 Control Panel 62
- 6-3 System Cooling 62
- System Fan Failure 63
- Accessing the Drive Bays 64
- Hard Drive Installation 64
- Peripheral Drive Installation 67
- 6-6 Power Supply 69
- Chapter 7 71
- 7-2 Main Setup 72
- XBOOT Features 74
- Power Confi guration 75
- Processor and Clock Options 75
- XAdvanced Chipset Control 77
- XCPU Bridge Confi guration 77
- XNorth Bridge Confi guration 79
- XSouthBridge Confi guration 80
- IDE/SATA/Floppy Confi guration 81
- XPCI/PnP Confi guration 84
- XRemote Access Confi guration 85
- Hardware Health Monitor 86
- XACPI Confi guration 88
- View BMC System Event Log 89
- Set LAN Confi guration 90
- IP Address Confi guration 91
- MAC Address Confi guration 92
- Subnet Mask Confi guration 92
- SEL PEF Confi guration 93
- XDMI Event Log 94
- 7-4 Security Settings 95
- 7-5 Boot Confi guration 96
- 7-6 Exit Options 97
- Appendix A 99
- BIOS Error Beep Codes 99
- Appendix B 101
- Installing Windows 101
- Appendix C 103
- System Specifi cations 103
Related products and manuals for Server barebones Supermicro 6016GT-TF
Server barebones Supermicro 182756 User Manual
(134 pages)
(134 pages)
© 2020, manymanuals.com. All rights reserved. | 0.637 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals