Supermicro A+ Server 1011M-URV, Silver User Manual

® SUPERAS1011M-UR USER’S MANUAL1.0c

xNotesAS1011M-UR User's Manual

B-8AS1011M-UR User's ManualNotes

C-1Appendix C: System Specifi cationsAppendix CSystem Specifi cationsProcessors Single AMD Opteron 1000 processor in AM2 socket Note: Please

C-2AS1011M-Ni User's ManualChassis SC815TQ-R450U Form Factor: 1U rackmount Dimensions: (WxHxD) 17 x 1.7 x 25.6 in. (432 x 43 x 650 mm

C-3Appendix C: System Specifi cationsCalifornia Best Management Practices Regulations for Perchlorate Materials: This Perchlorate warning applies only

C-4AS1011M-Ni User's Manual(continued from front)The products sold by Supermicro are not intended for and will not be used in life support system

Chapter 1 Introduction1-1 OverviewSupermicro's AS1011M-UR is an economic 1U rackmount server. The 1011M-UR is comprised of two main subsy

1-2AS1011M-UR User's Manual1-2 Motherboard FeaturesAt the heart of the 1011M-UR lies the H8SMU, a single processor motherboard based on the nVidi

1-3Chapter 1: Introduction Other FeaturesOther onboard features that promote system health include onboard voltage moni-tors, a chassis intrusion h

1-4AS1011M-UR User's Manual1-3 Server Chassis FeaturesThe 1011M-UR uses the SC815TQ-R450U 1U server chassis. The following is a general outline

1-5Chapter 1: Introduction1-4 Contacting SupermicroHeadquarters Address: Super Micro Computer, Inc. 980 Rock Ave.

1-6AS1011M-UR User's ManualNotes

Chapter 2: Server Installation2-1 Chapter 2 Server Installation 2-1 OverviewThis chapter provides a quick setup

2-2AS1011M-UR User's ManualChoosing a Setup Location - Leave enough clearance in front of the rack to enable you to open the front door comp

Chapter 2: Server Installation2-3Rack Mounting ConsiderationsAmbient Operating TemperatureIf installed in a closed or multi-unit rack assembly, the am

Manual Revision 1.0c Release Date: October 10, 2008Unless you request and receive written permission from Super Micro Computer, Inc., you may no

2-4AS1011M-UR User's Manual2-4 Installing the System into a RackThis section provides information on installing the 1011M-UR into a rack unit wi

Chapter 2: Server Installation2-5Installing the Outer RailsBegin by measuring the distance from the front rail to the rear rail of the rack. Attach a

2-6AS1011M-UR User's ManualFigure 2-3. Installing the Server into a RackInstalling the Server into the RackYou should now have rails attached to

Chapter 2: Server Installation2-7Figure 2-4. Installing the Server into a Telco RackInstalling the Server into a Telco RackTo install the 1011M-UR i

2-8AS1011M-UR User's Manual2-5 Checking the Motherboard SetupAfter you install the 1011M-UR in the rack, you will need to open the top cover to

Chapter 2: Server Installation2-9Figure 2-5. Accessing the Inside of the System

2-10AS1011M-UR User's Manual2-6 Checking the Drive Bay SetupNext, you should check to make sure the peripheral drives and the SAS/SATA drives an

Chapter 3: System Interface3-1Chapter 3 System Interface3-1 OverviewThere are several LEDs on the control panel as well as others on the SAS/S

3-2AS1011M-UR User's Manual3-3 Control Panel LEDsThe control panel located on the front of th SC815TQ-R450U chassis has fi ve LEDs. These LEDs p

Chapter 3: System Interface3-3 NIC2: Indicates network activity on LAN2 when fl ashing . NIC1: Indicates network activity on LAN1 when fl ashing.

PrefaceAbout This ManualThis manual is written for professional system integrators and PC technicians. It provides information for the installation a

3-4AS1011M-UR User's ManualSAS DrivesEach SAS drive carrier has two LEDs: Green: When illuminated, the green LED on the front of the SAS drive

Chapter 4: System Safety4-1 Chapter 4 System Safety!Basic electrical safety precautions should be followed to protect yourself from

AS1011M-UR User's Manual4-24-2 General Safety PrecautionsFollow these rules to ensure general safety:  Keep the area around the SuperServer 10

Chapter 4: System Safety4-34-3 ESD Precautions Electrostatic discharge (ESD) is generated by two objects with different electrical charges co

AS1011M-UR User's Manual4-44-4 Operating Precautions Care must be taken to assure that the chassis cover is in place when the 1011M-UR i

Chapter 5: Advanced Motherboard Setup5-1 Chapter 5 Advanced Motherboard SetupThis chapter covers the steps required to inst

5-2AS1011M-UR User's Manual5-2 Processor and Heatsink Installation!CPU Backplates A CPU backplate (BKT-0017L) has been included in the retail bo

Chapter 5: Advanced Motherboard Setup5-34. With the CPU inserted into the socket, inspect the four corners of the CPU to make sure that it is properly

5-4AS1011M-UR User's Manual5-3 Mounting the Motherboard into a ChassisAll motherboards and motherboards have standard mounting holes to fi t diff

Chapter 5: Advanced Motherboard Setup5-55-4 Connecting CablesNow that the processors are installed, the next step is to connect the cables to the mo

AS1011M-UR User's ManualivChapter 5: Advanced Motherboard SetupChapter 5 provides detailed information on the H8SMU motherboard, including the l

5-6AS1011M-UR User's ManualFigure 5-1. Front Control Panel Header Pins (JF1)Connecting the Control PanelJF1 contains header pins for various fron

Chapter 5: Advanced Motherboard Setup5-75-5 I/O PortsThe I/O ports are color coded in conformance with the PC 99 specifi cation. See Figure 5-2 below

5-8AS1011M-UR User's ManualTop View of DDR2 FBD SlotFigure 5-3. Installing DIMM into SlotTo Install: Insert module vertically and press down unti

Chapter 5: Advanced Motherboard Setup5-95-7 Adding PCI Cards1. PCI Expansion SlotsTwo riser cards are used to support add-on cards to the system. Th

5-10AS1011M-UR User's ManualFigure 5-4. SUPER H8SMU Layout(not drawn to scale)5-8 Motherboard DetailsNotes:Jumpers not indicated are for test pu

Chapter 5: Advanced Motherboard Setup5-11H8SMU Quick ReferenceJumper Description Default Setting JBT1 CMOS Clear See Section 5-10 JCF1

5-12AS1011M-UR User's Manual5-9 Connector Defi nitions ATX Power ConnectorThe primary ATX power supply con-nector (JPW1) meets the SSI (Super-set

Chapter 5: Advanced Motherboard Setup5-13NIC1 LEDThe NIC1 (Network Interface Control-ler) LED connection is located on pins 11 and 12 of JF1. Attach

5-14AS1011M-UR User's ManualPower Fail LED The Power Fail LED connection is located on pins 5 and 6 of JF1. Refer to the table on the right for

Chapter 5: Advanced Motherboard Setup5-15Fan HeadersThe H8SMU has fi ve fan headers, which are designated FAN1 through FAN5. See the table on the righ

vPrefaceNotes

5-16AS1011M-UR User's ManualATX PS/2 Keyboard and PS/2 Mouse PortsThe ATX PS/2 keyboard and the PS/2 mouse ports are located on the I/O backplane

Chapter 5: Advanced Motherboard Setup5-17Chassis Intrusion A Chassis Intrusion header is located at JL1. Attach the appropriate cable to inform you o

5-18AS1011M-UR User's ManualCompact Flash Power HeaderA Compact Flash Card Power header is located at JWF1. For the Compact Flash Card to work

Chapter 5: Advanced Motherboard Setup5-195-10 Jumper SettingsExplanation of JumpersTo modify the operation of the motherboard, jumpers can be use

5-20AS1011M-UR User's ManualNote: When enabled, the user needs to write their own application software in or-der to disable the Watch Dog timer.W

Chapter 5: Advanced Motherboard Setup5-21Compact Flash Master/Slave The JCF1 jumper allows you to assign either master or slave status a compact fl ash

5-22AS1011M-UR User's Manual5-11 Onboard Indicators LAN1/LAN2 LEDsThe Ethernet ports (located beside the VGA port) have two LEDs. On each Gb

Chapter 5: Advanced Motherboard Setup5-235-12 Floppy, IDE and SATA Drive ConnectionsUse the following information to connect the fl oppy and hard disk

5-24AS1011M-UR User's ManualIDE ConnectorThere are no jumpers to con-fi gure the onboard IDE#1 con-nectors. See the table on the right for pin de

Chapter 5: Advanced Motherboard Setup5-255-13 Enabling SATA RAIDSerial ATA (SATA)Serial ATA (SATA) is a physical storage interface that employs a sin

viTable of ContentsPrefaceAbout This Manual ... ii

5-26AS1011M-UR User's Manual2. Use the arrow keys to move to Advanced > Floppy/IDE/SATA Confi guration > nVidia RAID Setup and press the &l

Chapter 5: Advanced Motherboard Setup5-27Figure 5-5. SATA RAID Utility: Main ScreenFigure 5-6. SATA RAID Utility: Array List

5-28AS1011M-UR User's Manual5-14 Installing DriversAfter all the hardware and operating system have been installed, you need to install certain d

Chapter 6: Advanced Chassis Setup6-1Chapter 6Advanced Chassis Setup This chapter covers the steps required to install components and perform m

6-2AS1011M-UR User's ManualFigure 6-1. Chassis: Front and Rear ViewsSystem Reset6-2 Control PanelThe control panel (located on the front of the

Chapter 6: Advanced Chassis Setup6-36-3 System FansThree 4-cm heavy duty counter-rotating fans provide the cooling for the 1011M-UR. Each fan unit is

6-4AS1011M-UR User's ManualFigure 6-2. System Cooling Fans6-4 Drive Bay Installation/RemovalRemoving the Front BezelIf your system has a front

Chapter 6: Advanced Chassis Setup6-5Accessing the Drive BaysSATA Drives: Because of their hotswap capability, you do not need to access the inside of

6-6AS1011M-UR User's ManualSAS/SATA Drive Installation1. Mounting a SAS/SATA drive in a drive carrier The SAS/SATA drives are mounted in driv

Chapter 6: Advanced Chassis Setup6-72. Installing/removing hot-swap SAS/SATA drives The SAS/SATA drive carriers are all easily accessible at the fr

Chapter 4: System Safety 4-1 Electrical Safety Precautions ... 4-14-2 Gene

6-8AS1011M-UR User's ManualDVD-ROM and Floppy Drive InstallationThe top cover of the chassis must be opened to gain full access to the DVD-ROM an

Chapter 6: Advanced Chassis Setup6-96-5 Power SupplyThe 1011M-UR has a 450 watt redundant power supply confi guration consisting of two hot-swap power

6-10AS1011M-UR User's ManualFigure 6-6. Removing/Replacing the Power Supply

Chapter 7: BIOS7-1 Chapter 7 BIOS7-1 IntroductionThis chapter describes the AMIBIOS™ Setup utility for t

7-2AS1011M-UR User's Manual7-2 Main MenuWhen you fi rst enter AMI BIOS Setup Utility, you will see the Main Menu screen. You can always return to

Chapter 7: BIOS7-3PS/2 Mouse SupportSet this value to allow the PS/2 mouse support to be modifi ed. The options are Enabled, Disabled and Auto.Wait for

7-4AS1011M-UR User's ManualACPI HPET TableUse this setting to Enable or Disable the ACPI HPET Table.Power Button ModeAllows the user to change th

Chapter 7: BIOS7-5 Floppy/IDE/SATA Confi guration Floppy AMove the cursor to these fi elds via up and down <arrow> keys to select the fl oppy typ

7-6AS1011M-UR User's ManualBlock (Multi-Sector Transfer)Block mode boosts IDE drive performance by increasing the amount of data transferred. Onl

Chapter 7: BIOS7-7Serial ATA0/1 Primary/Secondary ChannelHighlight one of the items above and press <Enter> to access the submenu for that item.

viiiWake-On-LAN ... 5-17Wake-On-Ring ...

7-8AS1011M-UR User's Manualdrive support. Select "Disabled" to prevent AMI BIOS from using the S.M.A.R.T. Select "Enabled" to

Chapter 7: BIOS7-9 PCI/PnP Confi guration Clear NVRAMSelect Yes to clear NVRAM during boot-up. The options are Yes and No.Plug & Play OSSelect Y

7-10AS1011M-UR User's ManualIRQ3/IRQ4/IRQ5/IRQ7/IRQ9/IRQ10/IRQ11/IRQ14/IRQ15This feature specifi es the availability of an IRQ to be used by a PCI

Chapter 7: BIOS7-11 Advanced Chipset Confi guration NorthBridge Confi guration In addition to the below settings, the screen lists various clock an

7-12AS1011M-UR User's Manual ECC Confi guration DRAM ECC EnableDRAM ECC allows hardware to report and correct memory errors automati-cally. Opt

Chapter 7: BIOS7-13possibility of Electromagnetic Interference. PCIE Spread SpectrumUse this setting to Enable or Disable spread spectrum for the PCI

7-14AS1011M-UR User's Manual Event Log Confi gurationView Event LogHighlight this item and press <Enter> to view the contents of the event

Chapter 7: BIOS7-15Redirection After BIOS POST Options are Disable (no redirection after BIOS POST), Boot Loader (redirection during POST and during b

7-16AS1011M-UR User's Manual7-4 Boot MenuThis feature allows the user to confi gure the following items: Boot Device PriorityThis feature allows

Chapter 7: BIOS7-177-6 Exit MenuSelect the Exit tab from AMI BIOS Setup Utility screen to enter the Exit BIOS Setup screen.Save Changes and Exit When

Table of ContentsixChapter 7: BIOS 7-1 Introduction ...

7-18AS1011M-UR User's ManualNotes

Appendix A BIOS Error Beep CodesDuring the POST (Power-On Self-Test) routines, which are performed each time the system is powered o

A-2AS1011M-UR User's ManualNotes

B-1Appendix B: BIOS POST Checkpoint Codes Appendix B BIOS POST Checkpoint CodesWhen AMIBIOS performs the Power

B-2AS1011M-UR User's ManualCheckpoint Code Description E0h The onboard fl oppy controller if available is initialized. Next, beginning the

B-3Appendix B: BIOS POST Checkpoint CodesCheckpoint Code Description 03h The NMI is disabled. Next, checking for a soft reset or a power on co

B-4AS1011M-UR User's ManualCheckpoint Code Description 25h Interrupt vector initialization is done. Clearing the password if the POST DIA

B-5Appendix B: BIOS POST Checkpoint CodesCheckpoint Code Description 4Ch The memory below 1 MB has been cleared via a soft reset. Clearing the

B-6AS1011M-UR User's ManualCheckpoint Code Description 86h The password was checked. Performing any required programming before WIN-BIOS

B-7Appendix B: BIOS POST Checkpoint CodesCheckpoint Code Description A9h Returned from adaptor ROM at E000h control. Performing any initializa