Supermicro X9DRH-ITF User Manual Page 22
- Page / 111
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
1-14
X9DRH-7F/-iF/-7TF/-iTF Motherboard User’s Manual
It is strongly recommended that you use a high quality power supply that meets ATX
power supply Specication 2.02 or above. It must also be SSI compliant. (For more
information, please refer to the website at http://www.ssiforum.org/). Additionally, in
areas where noisy power transmission is present, you may choose to install a line
lter to shield the computer from noise. It is recommended that you also install a
power surge protector to help avoid problems caused by power surges.
1-7 Super I/O
The Super I/O supports two high-speed, 16550 compatible serial communication
ports (UARTs). Each UART includes a 16-byte send/receive FIFO, a programmable
baud rate generator, complete modem control capability and a processor interrupt
system. Both UARTs provide legacy speed with baud rate of up to 115.2 Kbps
as well as an advanced speed with baud rates of 250 K, 500 K, or 1 Mb/s, which
support higher speed modems.
The Super I/O provides functions that comply with ACPI (Advanced Conguration
and Power Interface), which includes support of legacy and ACPI power manage-
ment through an SMI or SCI function pin. It also features auto power management
to reduce power consumption.
1-8 Advanced Power Management
The new advanced power management features supported by this motherboard
include IPNM and ME. Please note that you will need to do following to use these
two new features:
•Use a power supply that supports PMBus 1.1 or 1.2.
•Install the NMView software in your system. NMView is optional and can be
purchased from Supermicro.
Intel
®
Intelligent Power Node Manager (NM) (Available
when the NMView utility is installed in the system)
The Intel
®
Intelligent Power Node Manager (IPNM) provides your system with
real-time thermal control and power management for maximum energy efciency.
Although IPNM Specication Version 1.5/2.0 is supported by the BMC (Baseboard
Management Controller), your system must also have IPNM-compatible Manage-
ability Engine (ME) rmware installed to use this feature.
Note: Support for IPNM Specication Version 1.5 or Vision 2.0 depends
on the power supply used in the system.
- X9DRH-7F 1
- X9DRH-iF 1
- X9DRH-7TF 1
- X9DRH-iTF 1
- About This Motherboard 3
- Manual Organization 3
- Contacting Supermicro 5
- Table of Contents 6
- Chapter 3 Troubleshooting 8
- Chapter 4 BIOS 8
- Chapter 1 9
- Overview 9
- CLOSE 1st 11
- OPEN 1st 11
- LANE1/2/3/4 18
- 1-3 Special Features 20
- 1-4 PC Health Monitoring 20
- 1-5 ACPI Features 21
- 1-6 Power Supply 21
- 1-7 Super I/O 22
- Manageability Engine (ME) 23
- •RMCP+ protocol supported 24
- Chapter 2 25
- Installation 25
- Product Disposal 27
- Precautions 28
- Unpacking 28
- WARNING! 29
- X9DRH-7F/iF/7TF/iF 35
- Chapter 2: Installation 37
- •Phillips Screwdriver 39
- •Pan head screws (9 pieces) 39
- Installing the Motherboard 40
- USB 4, 6 42
- Pin # Denition 42
- Pin # Denition 42
- 3. IPMI_LAN 44
- Front Control Panel 45
- B. PWR LED 46
- A. HDD LED 47
- B. NIC1 LED 47
- C. NIC2 LED 47
- A. OH/Fail/PWR Fail LED 48
- B. PWR Supply Fail 48
- A. Reset Button 49
- B. PWR Button 49
- 2-7 Connecting Cables 50
- Standby Power 53
- 2-8 Jumper Settings 57
- SAS Enable 60
- Jumper Settings 60
- 1-2 Enabled (Default) 60
- 2-3 Disabled 60
- C Bus to PCI-Exp. Slots 61
- LAN 1/LAN 2 62
- IPMI LAN 62
- (X8ST3-F) 62
- BMC Heartbeat LED 63
- Chapter 3 67
- Troubleshooting 67
- No Video 68
- System Boot Failure 68
- Memory Errors 69
- •System conguration 71
- Chapter 4 73
- 4-2 Main Setup 74
- Boot Feature 76
- •Type of CPU 77
- •CPU Signature 77
- •Microcode Patch 77
- Socket 1 CPU Information 78
- ChipsetConguration 82
- North Bridge 82
- QPIConguration 83
- DIMMConguration 84
- South Bridge 86
- SATAConguration 87
- SCUConguration 88
- PCIe/PCI/PnPConguration 88
- SuperIOConguration 90
- SerialPort1Conguration 90
- SerialPort2Conguration 90
- Console Redirection Settings 91
- ACPI Settings 94
- •ME BIOS Interface 96
- •ME Version 96
- 4-4 Event Logs 97
- 4-5 IPMI 99
- BMCNetworkConguration 100
- 4-6 Boot 101
- 4-7 Security 102
- 4-8 Save & Exit 103
- BIOS Error Beep Codes 105
- Appendix A 105
- Appendix B 107
Related products and manuals for Server/workstation motherboards Supermicro X9DRH-ITF
(107 pages)© 2020, manymanuals.com. All rights reserved. | 0.788 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals