Supermicro X8DTU-6TF+ User Manual Page 72
- Page / 111
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
4-4
X8DTU-6F+/X8DTU-6TF+/X8DTU-6(T)F+-LR User's Manual
tings in the BIOS to make sure that the CPU and System temperatures are
within normal range. Also check the front panel Overheat LED and make sure
that the Overheat LED is not on.
Adequate power supply: Make sure that the power supply provides adequate 5.
power to the system. Make sure that all power connectors are connected.
Please refer to our website for more information on minimum power require-
ment.
Proper software support: Make sure that the correct drivers are used. 6.
B. When the system becomes unstable before or during OS installation, check
the following.
Source of installation: Make sure that the devices used for installation are 1.
working properly, including boot devices such as CD/DVD disc, CD/DVD-
ROM.
Cable connection: Check to make sure that all cables are connected and 2.
working properly.
Using minimum confi guration for troubleshooting: Remove all unnecessary 3.
components, add-on cards fi rst, and use minimum confi guration (with a CPU
and a memory module installed) to identify the trouble areas. Refer to the
steps listed in Section A above for proper troubleshooting procedures.
Identifying bad components by isolating them: If necessary, remove a compo-4.
nent in question from the chassis, and test it in isolation to make sure that it
works properly. Replace a bad component with a good one.
Check and change one component at a time instead of changing several 5.
items at the same time. This will help isolate and identify problems.
To fi nd out if a component is good, swap this component with a new one to 6.
see if the system will work properly. If so, then the old component is bad.
You can also install the component in question in another system. If the new
system works, the component is good and the old system has problems.
4-2 Technical Support Procedures
Before contacting Technical Support, please take the following steps. Also, please
note that as a motherboard manufacturer, Supermicro does not sell directly to end-
users, so it is best to fi rst check with your distributor or reseller for troubleshooting
- X8DTU-6F+ 1
- X8DTU-6TF+ 1
- X8DTU-6F+-LR 1
- X8DTU-6TF+-LR 1
- About This Motherboard 3
- Manual Organization 3
- Contacting Supermicro 5
- Table of Contents 6
- Chapter 4 Troubleshooting 8
- Chapter 5 BIOS 8
- Chapter 1 9
- Quick Installation Guide 9
- Chapter 2 13
- Overview 13
- Motherboard Features 19
- System Block Diagram 22
- 2-2 Chipset Overview 23
- 2-3 Special Features 24
- 2-4 PC Health Monitoring 24
- 2-5 ACPI Features 25
- 2-6 Power Supply 25
- 2-8 Super I/O 26
- Chapter 3 27
- Installation 27
- Removing the Passive Heatsink 31
- Installing an Active Heatsink 32
- Removing the Active Heatsink 33
- Removing Memory Modules 34
- Memory Support 35
- Installed 36
- 1.35V DIMMs 37
- Installing the Motherboard 40
- 3. IPMI-Dedicated LAN 45
- 1. Rear UID Switch 46
- 2. Rear UID LED (LED 2) 46
- 3. FP UID Switch 46
- 4. FP UID LED 46
- B. PWR LED 48
- A. HDD LED 49
- B. FP UID Switch 49
- C. NIC1 Link LED 49
- D. NIC1 Activity LED 49
- A. NIC 2 Link LED 50
- B. NIC 2 Activity LED 50
- D. UID LED (Blue) 50
- A. PWR Fail LED 51
- B. Reset Button 51
- A. PWR Button 52
- 3-6 Connecting Cables 53
- A. Internal Speaker (Buzzer) 55
- A. DOM PWR 56
- B. Overheat LED 56
- A. T-SGPIO-1 57
- B. T-SGPIO-2 57
- C. PWR SMB 57
- A. UIO Power Connector 58
- B. SAS Battery-Backup Unit 58
- A. TPM Connector 59
- 3-7 Jumper Settings 60
- A. Clear CMOS 61
- B. Watch Dog Enable 61
- A. SAS Enable 63
- 3-8 Onboard LED Indicators 64
- A. UID LED 66
- B. BMC Heartbeat LED 66
- State Defi nition 66
- Blinking BMC: Normal 66
- LED Status 67
- SAS Error LED 67
- Connections 68
- Chapter 4 69
- Troubleshooting 69
- No Video 70
- System Boot Failure 70
- Memory Errors 71
- Chapter 5 75
- 5-2 Main Setup 76
- Boot Features 78
- Processor and Clock Options 79
- Advanced Chipset Control 82
- QPI and IMC Confi guration 82
- South Bridge Confi guration 85
- IDE/SATA Confi guration 86
- PCI/PnP Confi guration 89
- Remote Access Confi guration 90
- Hardware Health Monitor 91
- ACPI Confi guration 94
- Intel TXT(LT) Confi guration 95
- Trusted Computing (Optional) 96
- IPMI Confi guration 97
- View BMC System Event Log 97
- Set LAN Confi guration 98
- Event Log Confi guration 99
- 5-4 Security Settings 100
- 5-5 Boot Confi guration 101
- 5-6 Exit Options 102
- Motherboard User’s Manual 104
- BIOS Error Beep Codes 105
- Appendix A 105
- Appendix B 107
Comments to this Manuals
Related products and manuals for Server/workstation motherboards Supermicro X8DTU-6TF+
(113 pages)© 2020, manymanuals.com. All rights reserved. | 0.794 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Hello, im noob :)