Supermicro X8DTU-6TF+ User Manual Page 71
- Page / 111
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
4-3
Chapter 4: Troubleshooting
Memory Errors
When a No_Memory_Beep_Code is issued by the system, check the following:
Make sure that the memory modules are compatible and that the DIMM mod-1.
ules are properly and fully installed. (For memory compatibility, refer to the
Memory Compatibility Chart posted on our website @ http://www.supermicro.
com.)
Check if different speeds of DIMMs have been installed. It is strongly recom-2.
mended to use the same RAM speed for all DIMMs in the system.
Make sure you are using the correct type of DDR3 Registered/Load Reduced/ 3.
Unbuffered ECC or Non-ECC SDRAM modules as recommended by the
manufacturer. Refer to Page 2-6 for memory support.
Check for bad DIMM modules or slots by swapping a single module among 4.
all memory slots and check the results.
Make sure that all memory modules are fully seated in their slots. Follow the 5.
instructions given in Section 3-3 in Chapter 3.
Please follow the instructions given in the DIMM Population Tables listed in 6.
Section 3-3 to install your memory modules.
When the System Becomes Unstable
A. When the system becomes unstable during or after OS installation, check
the following:
OS Compatibility: Check if the OS is compatible with your system1.
CPU/BIOS support: Check if your CPU is supported and if you have the latest 1.
BIOS installed.
Memory support: Make sure that the memory modules are supported by test-2.
ing the modules using memtest86 or a similar utility.
Note: Refer to the product page on our website http:\\www.supermicro.
com for memory compatibility list.
HDD support: Check if all hard disk drives (HDDs) work properly. Replace the 3.
bad HDDs with good ones.
System cooling: Check system cooling to make sure that all heatsink fans, 4.
and CPU/system fans, etc., work properly. Check Hardware Monitoring set-
- X8DTU-6F+ 1
- X8DTU-6TF+ 1
- X8DTU-6F+-LR 1
- X8DTU-6TF+-LR 1
- About This Motherboard 3
- Manual Organization 3
- Contacting Supermicro 5
- Table of Contents 6
- Chapter 4 Troubleshooting 8
- Chapter 5 BIOS 8
- Chapter 1 9
- Quick Installation Guide 9
- Chapter 2 13
- Overview 13
- Motherboard Features 19
- System Block Diagram 22
- 2-2 Chipset Overview 23
- 2-3 Special Features 24
- 2-4 PC Health Monitoring 24
- 2-5 ACPI Features 25
- 2-6 Power Supply 25
- 2-8 Super I/O 26
- Chapter 3 27
- Installation 27
- Removing the Passive Heatsink 31
- Installing an Active Heatsink 32
- Removing the Active Heatsink 33
- Removing Memory Modules 34
- Memory Support 35
- Installed 36
- 1.35V DIMMs 37
- Installing the Motherboard 40
- 3. IPMI-Dedicated LAN 45
- 1. Rear UID Switch 46
- 2. Rear UID LED (LED 2) 46
- 3. FP UID Switch 46
- 4. FP UID LED 46
- B. PWR LED 48
- A. HDD LED 49
- B. FP UID Switch 49
- C. NIC1 Link LED 49
- D. NIC1 Activity LED 49
- A. NIC 2 Link LED 50
- B. NIC 2 Activity LED 50
- D. UID LED (Blue) 50
- A. PWR Fail LED 51
- B. Reset Button 51
- A. PWR Button 52
- 3-6 Connecting Cables 53
- A. Internal Speaker (Buzzer) 55
- A. DOM PWR 56
- B. Overheat LED 56
- A. T-SGPIO-1 57
- B. T-SGPIO-2 57
- C. PWR SMB 57
- A. UIO Power Connector 58
- B. SAS Battery-Backup Unit 58
- A. TPM Connector 59
- 3-7 Jumper Settings 60
- A. Clear CMOS 61
- B. Watch Dog Enable 61
- A. SAS Enable 63
- 3-8 Onboard LED Indicators 64
- A. UID LED 66
- B. BMC Heartbeat LED 66
- State Defi nition 66
- Blinking BMC: Normal 66
- LED Status 67
- SAS Error LED 67
- Connections 68
- Chapter 4 69
- Troubleshooting 69
- No Video 70
- System Boot Failure 70
- Memory Errors 71
- Chapter 5 75
- 5-2 Main Setup 76
- Boot Features 78
- Processor and Clock Options 79
- Advanced Chipset Control 82
- QPI and IMC Confi guration 82
- South Bridge Confi guration 85
- IDE/SATA Confi guration 86
- PCI/PnP Confi guration 89
- Remote Access Confi guration 90
- Hardware Health Monitor 91
- ACPI Confi guration 94
- Intel TXT(LT) Confi guration 95
- Trusted Computing (Optional) 96
- IPMI Confi guration 97
- View BMC System Event Log 97
- Set LAN Confi guration 98
- Event Log Confi guration 99
- 5-4 Security Settings 100
- 5-5 Boot Confi guration 101
- 5-6 Exit Options 102
- Motherboard User’s Manual 104
- BIOS Error Beep Codes 105
- Appendix A 105
- Appendix B 107
Comments to this Manuals
Related products and manuals for Server/workstation motherboards Supermicro X8DTU-6TF+
(113 pages)© 2020, manymanuals.com. All rights reserved. | 2.483 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Hello, im noob :)