Supermicro X10DRL-i User Manual Page 77
- Page / 121
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
Chapter 4: AMI BIOS
4-9
CPU P State Control (Available when Power Technology
is set to Custom)
EIST (P-states)
EIST (Enhanced Intel SpeedStep Technology) allows the system to automatically
adjust processor voltage and core frequency to reduce power consumption and
heat dissipation. The options are Disable and Enable.
Turbo Mode
Select Enabled to use the Turbo Mode to boost system performance. The options
are Enable and Disable.
P-state Coordination
This feature is used to change the P-state (Power-Performance State) coordi-
nation type. P-state is also known as "SpeedStep" for Intel processors. Select
HW_ALL to change the P-state coordination type for hardware components only.
Select SW_ALL to change the P-state coordination type for all software installed
in the system. Select SW_ANY to change the P-state coordination type for a soft-
ware program in the system. The options are HW_All, SW_ALL, and SW_ANY.
CPU C State Control (Available when Power Technology
is set to Custom)
Package C State limit
Use this item to set the limit on the C-State package register. The options are
C0/1 state, C2 state, C6 (non-Retention) state, and C6 (Retention) state.
CPU C3 Report
Select Enable to allow the BIOS to report the CPU C3 State (ACPI C2) to the
operating system. During the CPU C3 State, the CPU clock generator is turned
off. The options are Enable and Disable.
CPU C6 Report (Available when Power Technology is set to Custom)
Select Enable to allow the BIOS to report the CPU C6 state (ACPI C3) to the
operating system. During the CPU C6 state, power to all cache is turned off.
The options are Enable and Disable.
Enhanced Halt State (C1E)
Select Enabled to use Enhanced Halt-State technology, which will signicantly
reduce the CPU's power consumption by reducing the CPU's clock cycle and
voltage during a Halt-state. The options are Disable and Enable.
- X10DRL-i 1
- About This Motherboard 3
- Manual Organization 3
- Contacting Supermicro 5
- Table of Contents 6
- Chapter 3 Troubleshooting 7
- Chapter 4 BIOS 8
- Chapter 1 9
- Overview 9
- Chapter 1: Overview 11
- Motherboard Layout 11
- X10DRL-i Quick Reference 12
- Management 17
- Dimensions 17
- System Block Diagram 18
- 1-3 Special Features 20
- 1-4 PC Health Monitoring 20
- 1-5 ACPI Features 21
- 1-6 Power Supply 21
- Installed) 22
- Management Engine (ME) 22
- Chapter 2 23
- Installation 23
- Product Disposal 25
- Precautions 26
- Unpacking 26
- OPEN 1st 27
- Removing the Heatsink 32
- Rev. 1.01 33
- Capacity (GB) 34
- •Phillips Screwdriver 35
- •Pan head screws (8 pieces) 35
- Installing the Motherboard 36
- Front Control Panel 42
- B. PWR LED 43
- A. HDD LED/UID Switch 44
- B. NIC1 LED 44
- C. NIC2 LED 44
- B. PWR Supply Fail 45
- A. Reset Button 46
- B. PWR Button 46
- 2-7 Connecting Cables 47
- A. Internal Speaker 49
- (Buzzer) 49
- B. SATA DOM PWR 49
- B. JIPMB1 51
- A. I-SGPIO1 52
- B. I-SGPIO2 52
- C. S-SGPIO 52
- D. Standby PWR 52
- A. PWR LED/Speaker 53
- 2-8 Jumper Settings 54
- A. Clear CMOS 55
- B. Watch Dog Enable 55
- A. VGA Enabled 56
- B. BMC Enabled 56
- C. ME Select 57
- 2-9 Onboard LED Indicators 58
- 2-10 SATA Connections 60
- Chapter 3 61
- Troubleshooting 61
- No Video 62
- System Boot Failure 62
- Memory Errors 63
- •System conguration 65
- Proper Battery Disposal 66
- Battery Removal 66
- Chapter 4 69
- 4-2 Main Setup 70
- Boot Feature 72
- Power Conguration 73
- CPU Conguration 74
- Processor 1/Processor 2 74
- Chipset Conguration 79
- North Bridge 79
- IIO Conguration 79
- IIO1 Conguration 79
- IIO2 Conguration 79
- QPI Status 81
- Isoc Mode 82
- Memory Conguration 83
- •P1-DIMMA1 - P1-DIMMD1 84
- •P2-DIMME1 - P2-DIMMH1 84
- •USB Module Version 85
- •USB Devices 85
- •Software Preserve Support 87
- •ME Firmware Status #2 92
- •Current State 92
- •Error Code 92
- •PCI Bus Driver Version 92
- Super IO Conguration 94
- ACPI Settings 101
- 4-4 Event Logs 102
- View SMBIOS Event Log 103
- 4-5 IPMI 104
- •IPMI LAN Selection 105
- •IPMI Network Link Status 105
- 4-6 Security Settings 106
- 4-7 Boot Settings 107
- •Legacy Boot Order #1 109
- •UEFI Boot Order #1 109
- 4-8 Save & Exit 110
- Appendix A 113
- BIOS Error Beep Codes 113
- Appendix B 115
- B-2 Installing SuperDoctor5 116
- Appendix C 117
Related products and manuals for Server/workstation motherboards Supermicro X10DRL-i
(131 pages)© 2020, manymanuals.com. All rights reserved. | 1.969 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals