Supermicro X10SRG-F User Manual Page 77
- Page / 137
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
Chapter 4: AMI BIOS
4-5
Bootup Num-Lock
Use this feature to set the Power-on state for the Numlock key. The options are
Off and On.
Wait For 'F1' If Error
Select Enabled to force the system to wait until the 'F1' key is pressed if an error
occurs. The options are Disabled and Enabled.
INT19 (Interrupt 19) Trap Response
Interrupt 19 is the software interrupt that handles the boot disk function. When this
item is set to Immediate, the ROM BIOS of the host adaptors will "capture" Inter-
rupt 19 at bootup immediately and allow the drives that are attached to these host
adaptors to function as bootable disks. If this item is set to Postponed, the ROM
BIOS of the host adaptors will not capture Interrupt 19 immediately and allow the
drives attached to these adaptors to function as bootable devices at bootup. The
options are Immediate and Postponed.
Re-try Boot
When EFI Boot is selected, the system BIOS will automatically reboot the system
from an EFI boot device after its initial boot failure. Select Legacy Boot, to allow
the BIOS to automatically reboot the system from a Legacy boot device after its
initial boot failure. The options are Disabled, Legacy Boot, and EFI Boot.
Power Conguration
DeepSx Power Policies
UsethisitemtoconguretheAdvancedCongurationandPowerInterface(ACPI)
settings for the system. Enable S3 to use Standby Mode (Suspend-to-RAM) and
maintain power supply to the system RAM when the system is in the sleep mode.
Enable S4 to use Hibernation mode (Suspend to Disk) so that all data stored in of
the main memory can be saved in a non-volatile memory area such as in a hard
drive and then power down the system. Enable S5 to power off the whole system
except the power supply unit (PSU) and keep the power button "alive" so that the
user can "wake-up" the system by using an USB keyboard or mouse. The options
are Disabled, Enabled in S5, Enabled in S4-S5, and Enabled in S3-S4-S5.
Note: Exposed if motherboard designs it in.
GP27 Wake From DeepSx
Use this feature to enable or disable GP27 to wake from Deep Sx mode. The op-
tions are Enabled and Disabled.
Note: Exposed if motherboard designs it in.
- USER’S MANUAL 1
- X10SRG-F 1
- About This Motherboard 3
- Manual Organization 3
- Contacting Supermicro 5
- Table of Contents 6
- Chapter 3 Troubleshooting 8
- Chapter 4 BIOS 8
- •Six (6) SATA cables 15
- •One (1) I/O shield 15
- •One (1) User's Manual 15
- SATA DOM+POWER 17
- LGA2011-3 17
- Intel C610 18
- Motherboard Features 21
- FRONT PANEL 23
- SYSTEM POWER 23
- FAN SPEED 23
- 1-2 Chipset Overview 24
- 1-3 Special Features 25
- 1-4 PC Health Monitoring 25
- 1-5 ACPI Features 26
- 1-6 Power Supply 26
- Chapter 2 29
- Installation 29
- 2-2 Motherboard Installation 30
- Installing the Motherboard 31
- OPEN 1st 32
- WARNING! 32
- Removing the Heatsink 37
- 2-4 Installing DDR4 Memory 38
- Memory Support 39
- Memory Population Guidelines 39
- 1. IPMI LAN 5. LAN2 41
- 2. USB 3.0 Port 0 6. COM1 41
- 3. USB 3.0 Port 1 7. VGA 41
- Front Control Panel 45
- A. 20-Pin Main PWR 49
- B. 8-Pin GPU PWR (JPW2) 49
- C. 8-Pin GPU PWR (JPW3) 49
- (Required) 49
- A. Wake On LAN 51
- B. System Management Bus 51
- A. I-SGPIO1 53
- B. I-SGPIO2 53
- C. S-SGPIO 53
- D. TPM Header 53
- A. Overheat/Fan Fail LED 54
- B. Internal Speaker 54
- LAN Enable 56
- Jumper Settings 56
- SettingDenition 56
- Pins 1-2 Enabled (Default) 56
- Pins 2-3 Disabled 56
- PCI Slot SMB Enable (JI2C) 57
- Short Enabled (Default) 57
- Open Disabled 57
- LAN 1/LAN 2 61
- IPMI LAN 61
- (X8ST3-F) 61
- A. Unit ID LED 62
- B. Onboard Power LED 62
- 2-9 SATA Connections 63
- Chapter 3 65
- Troubleshooting 65
- No Video 66
- Memory Errors 66
- •Systemconguration 67
- Proper Battery Disposal 70
- Battery Installation 70
- Battery Removal 70
- Chapter 4 73
- 4-2 Main Setup 74
- Boot Feature 76
- Power Conguration 77
- CPU Conguration 78
- •CPU1 Version 79
- •CPU2 Version 79
- •L3 Cache RAM 79
- CPU P State Control 81
- CPU C State Control 81
- CPU T State Control 82
- Chipset Conguration 83
- North Bridge 83
- IIO Conguration 83
- IIO1 Conguration 83
- •Number of CPU 84
- •Number of IIO 84
- Memory Conguration 85
- DIMM Information 86
- Conguration 86
- •USB Module Version 87
- •USB Devices 87
- SATA Conguration 88
- •GeneralMEConguration 92
- •Recovery Firmware Version 92
- •ME Firmware Features 92
- PCIe/PCI/PnP Conguration 93
- Super IO Conguration 96
- COM1 Console Redirection 97
- X10SRG-F User’s Manual 100
- ACPI Settings 103
- •TPM Enabled Status 104
- •TPM Active Status 104
- •TPM Owner Status 104
- iSCSI Conrguration 105
- NIC Conguration 106
- Intel RSTe SATA Controller 107
- 4-4 Event Logs 108
- 4-5 IPMI 110
- BMC Network Conguration 111
- 4-6 Security Settings 113
- 4-7 Boot Settings 114
- 4-8 Save & Exit 117
- Appendix A 119
- BIOS Error Beep Codes 119
- Appendix B 121
- B-2 Installing SuperDoctor5 122
- Appendix C 123
- Appendix D 127
- D-1 IPMI GUI Browser 128
- Appendix D: Dual Boot Block 129
- D-2 IPMI Command Sets 133
- User Approach 135
Related products and manuals for Server/workstation motherboards Supermicro X10SRG-F
(113 pages)© 2020, manymanuals.com. All rights reserved. | 1.788 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals