Supermicro P4SC8 User Manual download pdf (Page 86)

C-16

SUPER P4SC8/P4SCi User's Manual

Rebuilding Arrays

Note 1: Rebuilding applies to Fault Tolerant array (RAID 1) only.

If an array Build process (or initialization) is interrupted or critical with one

member missing, you must perform a Rebuild to get the array to Optimal

status. For a critical array Rebuild operation, the optimal drive is the source

drive.

Note 2: If no spare array exists and a hard disk drive fails, you need to

create a spare before you can rebuild an array.

To Rebuild an array

1 From the Main Menu, select Manage Arrays (as shown in the screen

below). From the List of Arrays, select the array you want to Rebuild.

2 Press Ctrl+R to Rebuild.

1 2 ... 81 82 83 84 85 86 87 88 89 90 91 92 93 94

SUPER 1
About This Manual 3
Manual Organization 3
Table of Contents 4
Chapter 3: Troubleshooting 5
Chapter 4: BIOS 6
Appendices: 6
Chapter 1 7
Introduction 7
Contacting Supermicro 8
Chapter 1: Introduction 9
SUPER P4SC8/P4SCi 9
UPER P4SC8 10
P4SC8/P4SCi Quick Reference 11
Canterwood 12
Processor 0 12
Motherboard Features 13
System Memory Interface 15
System Features 15
1-3 PC Health Monitoring 16
1-5 Power Supply 17
1-6 Super I/O 18
Chapter 2 19
Installation 19
Heatsink 20
2-4 Installing DDR Memory 22
Memory Speeds 23
Front Control Panel 24
2-6 Connecting Cables 25
Reset Connector 26
PW_ON Connector 26
IR Connector 26
Power_LED Connector 27
Speaker Connector 27
*IDE LED (*See the note 27
Fan Headers 28
Serial Ports 28
Chassis Intrusion 29
ATX PS/2 Keyboard and 29
PS/2 Mouse Ports 29
Ethernet Ports GLAN1/2 30
VGA Connector 30
SATA LED 31
Universal Serial Bus (USB) 31
Wake-On-Ring 32
Keylock Enabled/Disabled 32
Wake-On-LAN 32
2-7 Jumper Settings 33
USB Wake-Up Enable 34
SCSI Enable 34
Front Side Bus Speeds 35
Watch Dog Enable/Disable 35
OH Fan Force-On Enable 36
VGA Enable 36
LAN 2Enable 37
Keyboard Wake-Up 37
Connections 38
IDE Connectors 39
Floppy Connector 39
SCSI Connectors 40
(*P4SC8 only) 40
Chapter 3 41
Troubleshooting 41
Memory Errors 42
Chapter 4 47
4-2 Running Setup 48
4-3 Main BIOS Setup 48
4-4 Advanced BIOS Setup 50
4-4.4 PnP Configuration 55
4-4.5 Console Redirection 56
4-4.6 Hardware Monitor 57
4-5 Security 59
4-6 Boot 60
4-7 Exit 61
Load Fail-Safe Defaults 62
Load Optimized Defaults 62
Discard Changes 62
Appendix A 63
BIOS POST Messages 63
Appendix B 65
Award BIOS POST Codes 65
Appendix C 71
Operating System 71
Enhanced Mode: 72
ATA Operate Mode 72
Combined Mode: 72
Managing Arrays 75
Creating Arrays 77
To create an array 77
RAID 1 Init 79
Initializing Disk Drives 83
Rebuilding Arrays 86
Using the Disk Utilities 87
Adaptec and Installing the OS 90
ATA RAID Controller Driver 91
Supero Doctor III 92

Comments to this Manuals

No comments

Supermicro P4SC8 User Manual Page 86

Comments to this Manuals

Related products and manuals for Motherboards Supermicro P4SC8