Supermicro P4SC8 User Manual Page 38
- Page / 94
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
2-20
SUPER P4SC8/P4SCi User's Manual
2-8 Parallel Port, Floppy Drive and Hard Drive
Connections
Use the following information to connect the floppy and hard disk drive
cables.
• The floppy disk drive cable has seven twisted wires.
• A red mark on a wire typically designates the location of pin 1.
• A single floppy disk drive ribbon cable has 34 wires and two connectors
to provide for two floppy disk drives. The connector with twisted wires
always connects to drive A, and the connector that does not have
twisted wires always connects to drive B.
• The 80-wire ATA100/66 IDE hard disk drive cable that came with your
system has two connectors to support two drives. This special cable
should be used to take advantage of the speed this new technology
offers. The blue connector connects to the onboard IDE connector inter-
face and the other connector(s) to your hard drive(s). Consult the docu-
mentation that came with your disk drive for details on actual jumper
locations and settings for the hard disk drive.
Parallel Port Connector
The parallel port is located on J8.
Refer to Figure 2-3 for location.
See the table on the right for pin
definitions.
Pin Number Function
1 Strobe-
3 Data Bit 0
5 Data Bit 1
7 Data Bit 2
9 Data Bit 3
11 Data Bit 4
13 Data Bit 5
15 Data Bit 6
17 Data Bit 7
19 ACK
21 BUSY
23 PE
25 SLCT
Pin Number Function
2 Auto Feed
-
4 Error-
6 Init-
8 SLCT IN-
10 GND
12 GND
14 GND
16 GND
18 GND
20 GND
22 GND
24 GND
26 NC
Parallel (Printer) Port Pin Definitions
(J8)
CPU
478 PGA
MCH
CPU FAN
COM2
USB 1/2
Parallel Port
KB/Mouse WakeUp
WOR
O
H
F
A
N
COM 1
VGA
GLAN 1
PCI 1-X
PCI-X 2
PCI 2
SCSI Channel A
BATTERY
BIOS
DIMM 0A
DIMM 0B
DIMM 1B
Watch Dog
FRONT PANEL CTR
BANK0
BANK1
Hance
Rapids
®
JF1
IR
Super I/O
Ext Speaker
SATA LED
Keylock
JBTL1
24-pin ATX
Conn
S
UPER P4SC8
GLAN 2
PCI 1
DIMM 1A
CHS FAN2
ID
E
2
KB/
Mouse
USBWakeUp
Cha Instr.
LAN2 Enable
+12V PWR
PWR Froce On
(North Bridge)
CHS FAN4
CHS FAN3
CPU SPeeds
SATA1
Clear CMOS
USB3/4
VGA Enable
GLAN CTLR
GLAN CTLR
OH Fan Force-On
External SCSI-B
SCSI
VGA
SCSI 1-2 Enable
ID
E1
WOL
PWR LED
CHS FAN1
CPU FAN
SATA2
Floppy
SMBus
Parallel Port
- SUPER 1
- About This Manual 3
- Manual Organization 3
- Table of Contents 4
- Chapter 3: Troubleshooting 5
- Chapter 4: BIOS 6
- Appendices: 6
- Chapter 1 7
- Introduction 7
- Contacting Supermicro 8
- Chapter 1: Introduction 9
- SUPER P4SC8/P4SCi 9
- UPER P4SC8 10
- P4SC8/P4SCi Quick Reference 11
- Canterwood 12
- Processor 0 12
- Motherboard Features 13
- System Memory Interface 15
- System Features 15
- 1-3 PC Health Monitoring 16
- 1-5 Power Supply 17
- 1-6 Super I/O 18
- Chapter 2 19
- Installation 19
- Heatsink 20
- 2-4 Installing DDR Memory 22
- Memory Speeds 23
- Front Control Panel 24
- 2-6 Connecting Cables 25
- Reset Connector 26
- PW_ON Connector 26
- IR Connector 26
- Power_LED Connector 27
- Speaker Connector 27
- *IDE LED (*See the note 27
- Fan Headers 28
- Serial Ports 28
- Chassis Intrusion 29
- ATX PS/2 Keyboard and 29
- PS/2 Mouse Ports 29
- Ethernet Ports GLAN1/2 30
- VGA Connector 30
- SATA LED 31
- Universal Serial Bus (USB) 31
- Wake-On-Ring 32
- Keylock Enabled/Disabled 32
- Wake-On-LAN 32
- 2-7 Jumper Settings 33
- USB Wake-Up Enable 34
- SCSI Enable 34
- Front Side Bus Speeds 35
- Watch Dog Enable/Disable 35
- OH Fan Force-On Enable 36
- VGA Enable 36
- LAN 2Enable 37
- Keyboard Wake-Up 37
- Connections 38
- IDE Connectors 39
- Floppy Connector 39
- SCSI Connectors 40
- (*P4SC8 only) 40
- Chapter 3 41
- Troubleshooting 41
- Memory Errors 42
- Chapter 4 47
- 4-2 Running Setup 48
- 4-3 Main BIOS Setup 48
- 4-4 Advanced BIOS Setup 50
- 4-4.4 PnP Configuration 55
- 4-4.5 Console Redirection 56
- 4-4.6 Hardware Monitor 57
- 4-5 Security 59
- 4-6 Boot 60
- 4-7 Exit 61
- Load Fail-Safe Defaults 62
- Load Optimized Defaults 62
- Discard Changes 62
- Appendix A 63
- BIOS POST Messages 63
- Appendix B 65
- Award BIOS POST Codes 65
- Appendix C 71
- Operating System 71
- Enhanced Mode: 72
- ATA Operate Mode 72
- Combined Mode: 72
- Managing Arrays 75
- Creating Arrays 77
- To create an array 77
- RAID 1 Init 79
- Initializing Disk Drives 83
- Rebuilding Arrays 86
- Using the Disk Utilities 87
- Adaptec and Installing the OS 90
- ATA RAID Controller Driver 91
- Supero Doctor III 92
Related products and manuals for Motherboards Supermicro P4SC8
Motherboards Supermicro H8DC8 User Manual
(78 pages)
(78 pages)
Motherboards Supermicro X8DTL-6F User Manual
(93 pages)
(93 pages)
Motherboards Supermicro X8DTL-I User Manual
(101 pages)
(101 pages)
Motherboards Supermicro C7SIM-Q User Manual
(105 pages)
(105 pages)
Motherboards Supermicro X7DVL-L User Manual
(89 pages)
(89 pages)
Motherboards Supermicro X8DTi-F User Manual
(98 pages)
(98 pages)
Motherboards Supermicro C2SBA+ Manual
(1 pages)
(1 pages)
Motherboards Supermicro H8DAE-2 User Manual
(82 pages)
(82 pages)
Motherboards Supermicro P4SCE User Manual
(92 pages)
(92 pages)
Motherboards Supermicro C2SBM-Q User Manual
(95 pages)
(95 pages)
Motherboards Supermicro X8STI-3F-O User Manual
(109 pages)
(109 pages)
Motherboards Supermicro H8DMU+ User Manual
(80 pages)
(80 pages)
Motherboards Supermicro X7DVL-E User Manual
(99 pages)
(99 pages)
Motherboards Supermicro PDSG4 User Manual
(95 pages)
(95 pages)
Motherboards Supermicro X8DA6 User Manual
(89 pages)
(89 pages)
Motherboards Supermicro X8DTN+ User Manual
(95 pages)
(95 pages)
© 2020, manymanuals.com. All rights reserved. | 2.126 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals