Supermicro X9SCM-iiF User Manual Page 23
- Page / 109
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
Chapter 1: Introduction
1-11
1-3 Special Features
Recovery from AC Power Loss
Basic I/O System (BIOS) provides a setting for you to determine how the system
will respond when AC power is lost and then restored to the system. You can
choose for the system to remain powered off (in which case you must press the
power switch to turn it back on), or for it to automatically return to a power-on state.
See the Advanced BIOS Setup section to change this setting. The default setting
is Last State.
1-4 PC Health Monitoring
This section describes the PC health monitoring features of the board. All have
an onboard System Hardware Monitoring chip that supports PC health monitoring.
An onboard voltage monitor will scan these onboard voltages continuously: CPU
Vcore, +3.3V, +5V, +/-12V, +3.3V Stdby, VBAT. Memory. Once a voltage becomes
unstable, a warning is given, or an error message is sent to the screen. The user
can adjust the voltage thresholds to dene the sensitivity of the voltage monitor.
Fan Status Monitor with Firmware Control
PC health monitoring in the BIOS can check the RPM status of the cooling fans. The
onboard CPU and chassis fans are controlled by Thermal Management via BIOS
(under the Hardware Monitoring section in the Advanced Setting).
Environmental Temperature Control
The thermal control sensor monitors the CPU temperature in real time and will turn
on the thermal control fan whenever the CPU temperature exceeds a user-dened
threshold. The overheat circuitry runs independently from the CPU. Once the ther-
mal sensor detects that the CPU temperature is too high, it will automatically turn
on the thermal fans to prevent the CPU from overheating. The onboard chassis
thermal circuitry can monitor the overall system temperature and alert the user when
the chassis temperature is too high.
Note: To avoid possible system overheating, please be sure to provide
adequate airow to your system.
System Resource Alert
This feature is available when the system is used with Supero Doctor III in
the Windows OS environment or used with Supero Doctor II in Linux. Supero
- X9SCM-IIF 1
- X9SCL-IIF 1
- About This Motherboard 3
- Manual Organization 3
- Contacting Supermicro 5
- Table of Contents 6
- •Six (6) SATA cables 13
- •One (1) I/O shield 13
- •One (1) User's Manual 13
- JL1:CHASSIS INTRUSION 16
- JWF1:DOM PWR 16
- •Two (2) (I-SATA 0/1) 19
- •RAID 0, 1 19
- •Four (4) (I-SATA 2~5) 19
- BLOCK DIAGRAM 21
- 1-2 Chipset Overview 22
- 1-3 Special Features 23
- 1-4 PC Health Monitoring 23
- 1-5 ACPI Features 24
- 1-6 Power Supply 24
- 1-7 Super I/O 25
- Chapter 2 27
- Installation 27
- Product Disposal 29
- 2-2 Static-Sensitive Devices 30
- Recommended Supermicro 34
- SNK-P0046P heatsink with BKT 34
- 0028L bottom bracket 34
- Removing the Heatsink 35
- Installing an Active Fan 36
- CPU Heatsink 36
- X9SCM/X9SCL(-F) Rev.1.0 39
- Memory Support 40
- Memory Population Guidelines 40
- 2-5 Motherboard Installation 42
- Installing the Motherboard 43
- 1. Keyboard (Purple) 45
- 2. Mouse (Green) 45
- 3.IPMI Dedicated LAN 47
- (NC: No Connection) 47
- Front Control Panel 50
- A. PWR LED 51
- B. HDD LED 51
- A. Reset Button 53
- B. PWR Button 53
- 2-7 Connecting Cables 54
- A. Internal Buzzer 56
- B. Speaker Header 56
- B. PWR SMB 57
- A.DOM PWR 59
- B. Stand-by Power 59
- 2-8 Jumper Settings 60
- PCI Slot SMB Enable 61
- Jumper Settings 61
- Short Enabled 61
- Open (Default) Disabled 61
- A. VGA Enable 62
- B. Watch Dog Timer Enable 62
- A. BP USB 0/1 Wake-up 63
- B. BMC Enable 63
- A. JPME1 64
- B. JPME2 64
- 2-9 Onboard Indicators 65
- 2-10 SATA Connections 67
- Chapter 3 69
- Troubleshooting 69
- No Video 70
- Memory Errors 70
- •System conguration 71
- User's Manual 72
- Proper Battery Disposal 74
- Battery Installation 74
- Battery Removal 74
- Chapter 4 77
- 4-2 Main Setup 78
- BOOT Feature 80
- Processor & Clock Options 81
- Chipset Conguration 83
- CPU Bridge Conguration 83
- Integrated IO Conguration 84
- South Bridge Conguration 84
- IDE/SATA Conguration 85
- PCIe/PCI/PnP Conguration 86
- Super IO Device Conguration 87
- ACPI Settings 89
- 4-4 Event Logs 90
- Chapter 4: AMI BIOS 91
- 4-5 IPMI Conguration 92
- BMC Network Conguration 93
- 4-6 Boot Settings 94
- Delete Boot Option 95
- 4-7 Security Settings 96
- 4-8 Save & Exit Options 97
- Appendix A 99
- BIOS Error Beep Codes 99
- Appendix B 101
- B-2 Conguring SuperDoctor 102
- Appendix C 105
Related products and manuals for Server/workstation motherboards Supermicro X9SCM-iiF
(88 pages)© 2020, manymanuals.com. All rights reserved. | 0.078 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals