Supermicro X10SAT User Manual Page 64
- Page / 113
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
3-4
X10SAT User’s Manual
3-3 Frequently Asked Questions
Question: What type of memory does my motherboard support?
Answer: The X10SAT supports up to 32GB of unbuffered Non-ECC DDR3 SDRAM
(1.5V, 1600/1333/1066 MHz). See Section 2-4 for details on installing memory.
Question: How do I update my BIOS?
Answer: We do NOT recommend that you upgrade your BIOS if you are not
experiencing any problems with your system. Updated BIOS les are located on
our website at http://www.supermicro.com/support/bios/. Please check our BIOS
warning message and the information on how to update your BIOS on our web
site. Select your motherboard model and download the BIOS ROM le to your
computer. Also, check the current BIOS revision to make sure that it is newer than
your BIOS before downloading. You may choose the zip le or the .exe le. If you
choose the zipped BIOS le, please unzip the BIOS le onto a bootable device or
a USB pen/thumb drive. To ash the BIOS, run the batch le named "ami.bat" with
the new BIOS ROM le from your bootable device or USB pen/thumb drive. Use
the following format:
F:\> ami.bat BIOS-ROM-lename.xxx <Enter>
Note: Always use the le named “ami.bat” to update the BIOS, and insert
a space between "ami.bat" and the lename. The BIOS-ROM-lename
will bear the motherboard name (i.e., X10SAT) and build version as the
extension. For example, "X10SAT.115". When completed, your system will
automatically reboot.
If you choose the .exe le, please run the .exe le under Windows to create
the BIOS ash oppy disk. Insert the oppy disk into the system you wish
to ash the BIOS. Then, boot the system to the oppy disk. The BIOS util-
ity will automatically ash the BIOS without any prompts. Please note that
this process may take a few minutes to complete. Do not be concerned if
the screen is paused for a few minutes.
When the BIOS ashing screen is completed, the system will reboot and
will show “Press F1 or F2”. At this point, you will need to load the BIOS
defaults. Press <F1> to go to the BIOS setup screen, and press <F3> to
load the default settings. Next, press <F4> to save and exit. The system
will then reboot.
Warning: Do not shut down or reset the system while updating the BIOS to prevent
possible system boot failure!
Important: The SPI BIOS chip installed on this motherboard is not re-
movable. To repair or replace a damaged BIOS chip, please send your
motherboard to RMA at Supermicro for service.
- USER’S MANUAL 1
- About This Motherboard 3
- Manual Organization 3
- Contacting Supermicro 5
- Table of Contents 6
- •Two (2) SATA cables 9
- •One (1) I/O shield 9
- X10SAT User’s Manual 10
- BIOS LICENSE 11
- Jumper Description Default 12
- Connector Description 13
- Motherboard Features 14
- 1-2 Chipset Overview 17
- 1-3 Special Features 18
- 1-4 PC Health Monitoring 18
- 1-5 ACPI Features 19
- 1-6 Power Supply 19
- 1-7 Super I/O 20
- Chapter 2 21
- Installation 21
- Product Disposal 23
- Precautions 24
- Unpacking 24
- Installing an Active CPU 28
- Heatsink with Fan 28
- Removing the Heatsink 30
- 2-4 Installing DDR3 Memory 31
- Memory Support 32
- Memory Population Guidelines 32
- Tools Needed 34
- Location of Mounting Holes 34
- Installing the Motherboard 35
- 2-6 Connectors/IO Ports 36
- DESIGNED IN USA 37
- A. HDMI Port 39
- B. VGA Port 39
- C. DVI Port 39
- Pin 15Pin 16 41
- A. Reset Button 43
- B. PWR Button 43
- 2-7 Connecting Cables 44
- A. PWR LED 47
- A. DOM PWR 48
- B. S/PDIF OUt 48
- A. STBY PWR 49
- A. AUDIO FP 51
- B. T-SGPIO 1 51
- C. T-SGPIO 2 51
- GLAN Enable 52
- Jumper Settings 52
- Pin# Denition 52
- 1-2 Enabled (default) 52
- 2-3 Disabled 52
- PCI Slot_SMB Enable 53
- Short Enabled 53
- Open (Default) Disabled 53
- USB Wake-Up 55
- Pins 1-2 Enabled 55
- Pins 2-3 Disabled (Default) 55
- BIOS Recovery (JBR1) 57
- 1-2 Normal (Default) 57
- 2-3 Recover 57
- 2-9 Onboard Indicators 58
- 2-10 SATA Connections 59
- Chapter 3 61
- Troubleshooting 61
- No Video 62
- Memory Errors 62
- •System conguration 63
- Battery Removal 65
- Proper Battery Disposal 65
- Battery Installation 66
- Chapter 4 67
- 4-2 Main Setup 68
- Boot Feature 70
- Power Conguration 71
- CPU Conguration 72
- •System Agent Bridge Name 78
- •VT-d Capability 78
- •IGFX VBIOS Version 78
- •IGfx Frequency 78
- PCI-E Conguration 80
- Memory Conguration 81
- •Intel PCH Rev ID 82
- •USB Conguration 82
- On Board Chip Conguration 83
- •Software Preserve Support 84
- ACPI Settings 87
- Detected) 87
- •ME FW Version 88
- •ME Firmware Mode 88
- •ME Firmware Type 88
- •ME Firmware SKU 88
- •PTT Capability/State 88
- Super IO Conguration 89
- H/W (Hardware) Monitor 90
- •Intel Sample Code Version 91
- •Thunderbolt Host Chip 91
- 4-4 Event Logs 94
- 4-5 Boot Settings 95
- •1st Device 96
- •2nd Device 96
- •1st Boot Device 96
- 4-6 Security Settings 97
- 4-7 Save & Exit 98
- Appendix A 101
- BIOS Error Beep Codes 101
- Appendix B 103
- B-2 Conguring SuperDoctor 104
- Appendix C 107
- Dual Boot Block 111
- Appendix D 111
Related products and manuals for Server/workstation motherboards Supermicro X10SAT
(123 pages)© 2020, manymanuals.com. All rights reserved. | 0.880 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals