Supermicro X7QC3 User Manual Page 16
- Page / 96
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
1-10
X7QC3/X7QCE User's Manual
1-3 Special Features
Recovery from AC Power Loss
BIOS provides a setting for you to determine how the system will respond when
AC power is lost and then restored to the system. You can choose for the system
to remain powered off (in which case you must hit the power switch to turn it
back on) or for it to automatically return to a power-on state. See the Power Lost
Control setting in the Advanced Setup section to change this setting. The default
setting is Last State.
1-4 PC Health Monitoring
This section describes the PC health monitoring features of the X7QC3/X7QCE.
All have an onboard System Hardware Monitor chip that supports PC health
monitoring.
Onboard Voltage Monitors for the CPU Cores, Chipset Voltage,
Memory Voltage, +1.8V, +3.3V, +5V, +12V, -12V, +3.3V Standby,
+5V Standby and VBAT.
An onboard voltage monitor will scan these voltages continuously. Once a voltage
becomes unstable, a warning is given or an error message is sent to the screen.
The user can adjust the voltage thresholds to defi ne the sensitivity of the voltage
monitor.
Fan Status Monitor with Firmware Control
The PC health monitor can check the RPM status of the cooling fans. The onboard
CPU and chassis fans are controlled by Thermal Management via BIOS (under
Hardware Monitoring in the Advanced Setting).
Environmental Temperature Control
The thermal control sensor monitors the CPU temperature in real time and will
turn on the thermal control fan whenever the CPU temperature reaches a user-
defi ned threshold. The overheat circuitry runs independently from the CPU. Once
it detects that the CPU temperature is too high, it will automatically turn on the
thermal fan control to lower the CPU temperature. The onboard chassis thermal
circuitry can monitor the overall system temperature and alert the user when the
chassis temperature is too high.
System Resource Alert
This feature is available when used with Supero Doctor III in the Windows OS
environment or used with Supero Doctor II in Linux. Supero Doctor is used to
notify the user of certain system events. For example, if the system is running
low on virtual memory and there is insuffi cient hard drive space for saving the
data, you can be alerted of the potential problem. You can also confi gure Supero
- SUPER 1
- Preface 3
- Table of Contents 4
- Chapter 3: Troubleshooting 6
- Chapter 4: BIOS 6
- Appendices: 6
- Chapter 1 7
- Introduction 7
- Contacting Supermicro 8
- Quick Reference X7QC3/X7QCE 11
- Motherboard Features 12
- 14
- 1-2 Chipset Overview 15
- 1-3 Special Features 16
- 1-4 PC Health Monitoring 16
- 1-5 ACPI Features 17
- 1-7 Super I/O 18
- 1-6 Power Supply 18
- Chapter 1: Introduction 19
- Chapter 2 21
- Installation 21
- Installation Procedures 22
- Warning! Make 23
- To Uninstall the Heatsink 24
- Memory Support 25
- Back Panel Connectors 27
- B. Front Control Panel 28
- Power LED 29
- NMI Button 29
- NIC1/NIC2 LED Indicators 30
- Overheat/Fan Fail LED (OH) 31
- Power Fail LED 31
- Power Button 32
- Reset Button 32
- 2-5 Connecting Cables 33
- Universal Serial Bus (USB) 34
- Chassis Intrusion 34
- Fan Headers 35
- . The default setting is 35
- ATX PS/2 Keyboard and 36
- PS/2 Mouse Ports 36
- Serial Ports 36
- Wake-On-Ring 37
- Wake-On-LAN 37
- Power LED/Speaker 38
- GLAN 1/2 (Gigabit Ethernet 38
- VGA Connector 39
- SGPIO Header 39
- Power SMB (I 40
- C) Connector 40
- Alarm Reset 40
- Overheat LED/Fan Failure 41
- Compact Flash Card PWR 41
- Connector 41
- IPMB Header 42
- CMOS Clear 44
- Watch Dog Enable/Disable 44
- A. VGA Enabled 45
- Onboard SAS Enable/ 46
- MegaRAID Enable 46
- Compact Flash Master/Slave 46
- CPU Power Select 47
- 3rd PWR Supply PWR Fault 47
- 2-7 Onboard Indicators 48
- SAS Activity LED Indicator 49
- LED Color Defi nition 49
- On SAS: Active 49
- Off SAS: Not Active 49
- Floppy Connector 50
- SIMSO Slot 50
- IDE Connectors 51
- Chapter 3 53
- Troubleshooting 53
- Memory Errors 54
- Chapter 4 57
- 4-2 Main Setup 58
- 4-3 Advanced Settings 59
- IDE Confi guration Submenu 60
- Floppy Confi guration 63
- PCI/PnP Confi guration 63
- Super IO Confi guration 64
- Chipset Settings 64
- Event Log Confi guration 68
- APCI Confi guration 68
- AHCI Confi guration 69
- APM Confi guration 69
- Hardware Health Confi guration 71
- SMBIOS Confi guration 73
- Remote Access Confi guration 73
- X7QC3/X7QCE User’s Manual 74
- Terminal Type 74
- VT-UTF8 Comb Key Support 74
- Sredir Memory Display Delay 74
- 4-4 Boot Confi guration 75
- Boot Device Priority 76
- Hard Disk Drive 77
- Removable Drives 77
- CD/DVD Drives 77
- 4-5 Security Settings 78
- 4-6 Exit Options 79
- Discard Changes 80
- Load Optimal Defaults 80
- Load Fail-Safe Defaults 80
- Appendix A 81
- BIOS POST Codes 81
- Important Notes to the User: 83
- Serial ATA (SATA) 83
- The Intel Matrix Storage 84
- Creating a RAID 0 Volume: 86
- Creating a RAID 1 Volume: 87
- Deleting RAID Volume: 90
- Appendix C 93
Related products and manuals for Server/workstation motherboards Supermicro X7QC3
(95 pages)© 2020, manymanuals.com. All rights reserved. | 1.173 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals