Supermicro X10SLA-F User Manual Page 64
- Page / 111
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
3-4
X10SLA/X10SLA-F User’s Manual
3-3 Frequently Asked Questions
Question: What type of memory does my motherboard support?
Answer: The X10SLA/X10SLA-F supports up to 32GB of Unbuffered ECC DDR3
SDRAM (1.35V/1.5V, 1600/1333 MHz). See Section 2-4 for details on installing
memory.
Question: How do I update my BIOS?
Answer: We do NOT recommend that you upgrade your BIOS if you are not
experiencing any problems with your system. Updated BIOS les are located on
our website at http://www.supermicro.com/support/bios/. Please check our BIOS
warning message and the information on how to update your BIOS on our web
site. Select your motherboard model and download the BIOS ROM le to your
computer. Also, check the current BIOS revision to make sure that it is newer than
your BIOS before downloading. You may choose the zip le or the .exe le. If you
choose the zipped BIOS le, please unzip the BIOS le onto a bootable device or
a USB pen/thumb drive. To ash the BIOS, run the batch le named "ami.bat" with
the new BIOS ROM le from your bootable device or USB pen/thumb drive. Use
the following format:
F:\> ami.bat BIOS-ROM-lename.xxx <Enter>
Note: Always use the le named “ami.bat” to update the BIOS, and insert
a space between "ami.bat" and the lename. The BIOS-ROM-lename
will bear the motherboard name (i.e., X10SLA/X10SLA-F) and build
version as the extension. For example, "X10SLA/X10SLA-F.115". When
completed, your system will automatically reboot.
If you choose the .exe le, please run the .exe le under Windows to create
the BIOS ash oppy disk. Insert the oppy disk into the system you wish
to ash the BIOS. Then, boot the system to the oppy disk. The BIOS util-
ity will automatically ash the BIOS without any prompts. Please note that
this process may take a few minutes to complete. Do not be concerned if
the screen is paused for a few minutes.
When the BIOS ashing screen is completed, the system will reboot and
will show “Press F1 or F2”. At this point, you will need to load the BIOS
defaults. Press <F1> to go to the BIOS setup screen, and press <F9> to
load the default settings. Next, press <F10> to save and exit. The system
will then reboot.
Warning: Do not shut down or reset the system while updating the BIOS to prevent
possible system boot failure!
- X10SLA-F 1
- About This Motherboard 3
- Manual Organization 3
- Contacting Supermicro 5
- Table of Contents 6
- •One (1) I/O shield 9
- •Six (6) SATA cables 9
- X10SLA/X10SLA-F User’s Manual 10
- Important Notes to the User 11
- X10SLA(-F) 12
- Motherboard Features 14
- 1-2 Chipset Overview 17
- 1-3 Special Features 18
- 1-4 PC Health Monitoring 18
- 1-5 ACPI Features 19
- 1-6 Power Supply 19
- 1-7 Super I/O 20
- Chapter 2 21
- Installation 21
- Product Disposal 23
- Precautions 24
- Unpacking 24
- Recommended Supermicro 28
- SNK-P0046P heatsink with BKT 28
- 0028L bottom bracket 28
- Removing the Heatsink 29
- Installing an Active CPU 30
- Heatsink with Fan 30
- Rev. 1.01 33
- Removing Memory Modules 34
- Memory Support 34
- Memory Population Guidelines 34
- Installing the Motherboard 37
- 2-6 Connectors/IO Ports 38
- A. UID SW 41
- B. UID LED (LE4) 41
- B. PWR LED 43
- A. HDD LED 44
- B. NIC1 LED 44
- C. NIC2 LED 44
- B. PWR Fail LED 45
- A. Reset Button 46
- B. PWR Button 46
- 2-7 Connecting Cables 47
- A. Internal Buzzer 49
- B. Onboard PWR LED 49
- Standby Power 50
- A. T-SGPIO 1/2 51
- B. PWR SMB 51
- A. TPM/Port 80 52
- GLAN Enable 53
- Jumper Settings 53
- Pin# Denition 53
- 1-2 Enabled (default) 53
- 2-3 Disabled 53
- PCI Slot_SMB Enable 54
- Pins 1-2 Enabled 54
- Pins 2-3 (Default) Disabled 54
- A. VGA Enable 55
- B. Watch Dog 55
- A. JPME1 56
- B. JPME2 56
- Backplane USB Wake_Up 57
- 1-2 Enabled (Default) 57
- Link LED Activity LED 58
- IPMI LAN 58
- A. PWR LED 59
- B. BMC Heartbeat LED 59
- (X10SLA-F) 59
- 2-10 SATA Connections 60
- Chapter 3 61
- Troubleshooting 61
- No Video 62
- Memory Errors 62
- •System conguration 63
- Proper Battery Disposal 65
- Battery Removal 65
- Battery Installation 66
- Chapter 4 67
- 4-2 Main Setup 68
- Boot Feature 70
- Power Conguration 71
- CPU Conguration 72
- •System Agent Bridge Name 77
- •VT-d Capability 77
- Memory Conguration 78
- •Row Precharge (tRPmin) 79
- •Intel PCH Rev ID 79
- •USB Conguration 79
- •USB Devices 79
- SATA Conguration 80
- •Software Preserve Support 81
- ACPI Settings 84
- Super IO Conguration 86
- Console Redirection Settings 86
- 4-4 Event Logs 90
- View SMBIOS Event Log 91
- •IPMI Firmware Revision 92
- •IPMI Status 92
- BMC Network Conguration 93
- 4-6 Boot Settings 94
- •1st Boot Device 95
- 4-7 Security Settings 96
- 4-8 Save & Exit 97
- Appendix A 99
- BIOS Error Beep Codes 99
- Appendix B 101
- Appendix C 105
- X10SAE User’s Manual 106
- Appendix D 109
- Dual Boot Block 109
Related products and manuals for Server/workstation motherboards Supermicro X10SLA-F
(119 pages)© 2020, manymanuals.com. All rights reserved. | 6.044 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals