Supermicro 1026GT-TF User Manual Page 75
- Page / 104
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
Chapter 7: BIOS
7-7
tion and heat dissipation. Please refer to Intel’s web site for detailed information.
The options are Disable (Disable GV3) and Enable (Enable GV3).
Intel® TurboMode Technology
Select Enabled to allow the processor cores to run faster than normal under special
circumstances to improve performance. The options are Disable and Enabled.
Intel® C-State Tech
If enabled, C-State is set by the system automatically to either C2, C3 or C4 state.
The options are Disabled and Enabled.
C-State package limit setting (Available when Intel® C-State Tech is
enabled)
If set to Auto, the AMI BIOS will automatically set the limit on the C-State package
register. The options are Auto, C1, C3, C6 and C7.
C1 Auto Demotion
When enabled, the CPU will conditionally demote C3, C6 or C7 requests to C1 based
on un-core auto-demote information. The options are Disabled and Enabled.
C3 Auto Demotion
When enabled, the CPU will conditionally demote C6 or C7 requests to C3 based
on un-core auto-demote information. The options are Disabled and Enabled.
Clock Spread Spectrum
Select Enable to use the feature of Clock Spectrum, which will allow the BIOS to
monitor and attempt to reduce the level of Electromagnetic Interference caused by
the components whenever needed. The options are Disabled and Enabled.
XAdvanced Chipset Control
The items included in the Advanced Settings submenu are listed below:
XCPU Bridge Confi guration
QPI Links Speed
This feature selects QPI's data transfer speed. The options are Slow-mode, and
Full Speed.
QPI Frequency
This selects the desired QPI frequency. The options are Auto, 4.800 GT,
5.866GT, 6.400 GT.
- SUPER 1
- Manual Revision 1.0 2
- About This Manual 3
- Manual Organization 3
- Table of Contents 6
- Chapter 3 System Interface 7
- Chapter 4 System Safety 7
- Chapter 1 9
- Introduction 9
- 1-2 Serverboard Features 10
- 1-3 Server Chassis Features 11
- 1-4 GPU Subsystem 12
- Chapter 1: Introduction 13
- System Block Diagram 13
- 1-5 Contacting Supermicro 14
- Chapter 2 15
- Server Installation 15
- Warnings and Precautions! 16
- Rack Mounting Considerations 17
- Assembling the Outer Rails 20
- Chapter 3 27
- System Interface 27
- 3-3 Control Panel LEDs 28
- 3-4 SATA Drive Carrier LEDs 29
- Chapter 4 31
- System Safety 31
- 4-3 ESD Precautions 33
- LITHIUM BATTERY 34
- BATTERY HOLDER 34
- Chapter 5 35
- Advanced Serverboard Setup 35
- 5-2 Serverboard Installation 36
- 5-3 Connecting Cables 37
- 5-4 I/O Ports 38
- Socket Clip Load Plate 39
- Plastic Cap 39
- CPU Socket 40
- Load Plate 40
- Installing a CPU Heatsink 41
- 5-6 Installing Memory 42
- DIMM Population Table 43
- 5-6 Adding PCI Add-On Cards 44
- 5-7 Serverboard Details 45
- X8DTG-DF Quick Reference 46
- 5-8 Connector Defi nitions 47
- 5-9 Jumper Settings 53
- 5-10 Onboard Indicators 55
- 5-11 SATA Ports 56
- 5-12 Installing Software 57
- Supero Doctor III 58
- Chapter 6 61
- Advanced Chassis Setup 61
- 6-2 Control Panel 62
- 6-3 System Cooling 62
- System Fan Failure 63
- Figure 6-3: Fan Numbering 64
- Installing the Air Shroud 65
- Accessing the Drive Bays 65
- Hard Drive Installation 65
- 6-5 Power Supply 68
- Chapter 7 69
- 7-2 Main Setup 70
- XBoot Features 72
- Power Confi guration 73
- Processor and Clock Options 73
- XAdvanced Chipset Control 75
- XCPU Bridge Confi guration 75
- XNorth Bridge Confi guration 78
- XSouth Bridge Confi guration 78
- IDE/SATA/Floppy Confi guration 79
- XPCI/PnP Confi guration 82
- XRemote Access Confi guration 83
- Hardware Health Confi guration 84
- XACPI Confi guration 86
- XGeneral WHEA Confi guration 87
- XIPMI Confi guration 87
- View BMC System Event Log 87
- Set LAN Confi guration 88
- IP Address Confi guration 89
- MAC Address Confi guration 89
- Subnet Mask Confi guration 89
- 7-4 Security Settings 90
- 7-5 Boot Confi guration 92
- 7-6 Exit Options 93
- 7-7 BIOS Recovery 94
- Flash") 95
- Confirm update BIOS? (y/n) y 96
- Starting remote flash 96
- Appendix A 99
- BIOS Error Beep Codes 99
- Appendix B 101
- System Specifi cations 101
Related products and manuals for Server barebones Supermicro 1026GT-TF
(98 pages)
(42 pages)© 2020, manymanuals.com. All rights reserved. | 1.656 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals