Supermicro 1026GT-TF User Manual download pdf (Page 66)

6-6

SUPERSERVER 1026GT-TF Series User's Manual

Figure 6-5: Removing a Hard Drive Carrier

Remove the dummy drive, which comes pre-installed in the drive carrier, by 1.

removing the screws securing the dummy drive to the carrier. Note that these

screws cannot be reused on the actual 2.5" hard drive.

Insert a drive into the carrier with the PCB side facing down and the connec-2.

tor end toward the rear of the carrier.

1 2 ... 61 62 63 64 65 66 67 68 69 70 71 ... 103 104

SUPER 1
Manual Revision 1.0 2
About This Manual 3
Manual Organization 3
Table of Contents 6
Chapter 3 System Interface 7
Chapter 4 System Safety 7
Chapter 1 9
Introduction 9
1-2 Serverboard Features 10
1-3 Server Chassis Features 11
1-4 GPU Subsystem 12
Chapter 1: Introduction 13
System Block Diagram 13
1-5 Contacting Supermicro 14
Chapter 2 15
Server Installation 15
Warnings and Precautions! 16
Rack Mounting Considerations 17
Assembling the Outer Rails 20
Chapter 3 27
System Interface 27
3-3 Control Panel LEDs 28
3-4 SATA Drive Carrier LEDs 29
Chapter 4 31
System Safety 31
4-3 ESD Precautions 33
LITHIUM BATTERY 34
BATTERY HOLDER 34
Chapter 5 35
Advanced Serverboard Setup 35
5-2 Serverboard Installation 36
5-3 Connecting Cables 37
5-4 I/O Ports 38
Socket Clip Load Plate 39
Plastic Cap 39
CPU Socket 40
Load Plate 40
Installing a CPU Heatsink 41
5-6 Installing Memory 42
DIMM Population Table 43
5-6 Adding PCI Add-On Cards 44
5-7 Serverboard Details 45
X8DTG-DF Quick Reference 46
5-8 Connector Deﬁ nitions 47
5-9 Jumper Settings 53
5-10 Onboard Indicators 55
5-11 SATA Ports 56
5-12 Installing Software 57
Supero Doctor III 58
Chapter 6 61
Advanced Chassis Setup 61
6-2 Control Panel 62
6-3 System Cooling 62
System Fan Failure 63
Figure 6-3: Fan Numbering 64
Installing the Air Shroud 65
Accessing the Drive Bays 65
Hard Drive Installation 65
6-5 Power Supply 68
Chapter 7 69
7-2 Main Setup 70
XBoot Features 72
Power Conﬁ guration 73
Processor and Clock Options 73
XAdvanced Chipset Control 75
XCPU Bridge Conﬁ guration 75
XNorth Bridge Conﬁ guration 78
XSouth Bridge Conﬁ guration 78
IDE/SATA/Floppy Conﬁ guration 79
XPCI/PnP Conﬁ guration 82
XRemote Access Conﬁ guration 83
Hardware Health Conﬁ guration 84
XACPI Conﬁ guration 86
XGeneral WHEA Conﬁ guration 87
XIPMI Conﬁ guration 87
View BMC System Event Log 87
Set LAN Conﬁ guration 88
IP Address Conﬁ guration 89
MAC Address Conﬁ guration 89
Subnet Mask Conﬁ guration 89
7-4 Security Settings 90
7-5 Boot Conﬁ guration 92
7-6 Exit Options 93
7-7 BIOS Recovery 94
Flash") 95
Confirm update BIOS? (y/n) y 96
Starting remote flash 96
Appendix A 99
BIOS Error Beep Codes 99
Appendix B 101
System Speciﬁ cations 101

Comments to this Manuals

No comments

Supermicro 1026GT-TF User Manual Page 66

Comments to this Manuals

Related products and manuals for Server barebones Supermicro 1026GT-TF