Supermicro X7SBA User Manual Page 17
- Page / 89
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
Chapter 1: Introduction
1-11
BIOS Support for USB Keyboard
If the USB keyboard is the only keyboard in the system, this keyboard will function
like a normal keyboard during system boot-up.
Main Switch Override Mechanism
When an ATX power supply is used, the power button can function as a system
suspend button. When the user presses the power button, the system will enter
a SoftOff state. The monitor will be suspended and the hard drive will spin down.
Pressing the power button again will cause the whole system to wake-up. Dur-
ing the SoftOff state, the ATX power supply provides power to keep the required
circuitry in the system "alive". In case the system malfunctions, and you want to
turn off the power, just press and hold the power button for 4 seconds. The power
will turn off and no power will be provided to the motherboard.
Wake Ring-On (WOR)
Wake-up events can be triggered by a device such as the external modem ringing
when the system is in the SoftOff state. Note that external modem ring-on can
only be used with an ATX 2.01 (or above) compliant power supply.
Wake-On-LAN (WOL)
Wake-On-LAN is dened as the ability of a management application to remotely
power up a computer that is powered off. Remote PC setup, up-dates and asset
tracking can occur after hours and on weekends so that daily LAN trafc is kept
to a minimum and users are not interrupted. The motherboard has a 3-pin header
(WOL) to connect to the 3-pin header on a Network Interface Card (NIC) that has
WOL capability. In addition, an onboard LAN controller can also support WOL
without any connection to the WOL header. The 3-pin WOL header is to be used
with a LAN add-on card only.
Note: Wake-On-LAN requires an ATX 2.01 (or above) compliant power supply.
1-5 ACPI Features
ACPI stands for Advanced Conguration and Power Interface. The ACPI speci-
cation denes a exible and abstract hardware interface that provides a standard
way to integrate power management features throughout a PC system, including
its hardware, operating system and application software. This enables the system
to automatically turn on and off peripherals such as CD-ROMs, network cards,
hard disk drives and printers. This also includes consumer devices connected to
the PC such as VCRs, TVs, telephones and stereos.
In addition to enabling operating system-directed power management, ACPI
provides a generic system event mechanism for Plug and Play and an operating
system-independent interface for conguration control. ACPI leverages the Plug
- X7SBA 1
- About This Manual 3
- Manual Organization 3
- Table of Contents 4
- Chapter 3: Troubleshooting 5
- Chapter 4: BIOS 6
- Appendices: 6
- Chapter 1 7
- Introduction 7
- Contacting Supermicro 8
- Chapter 1: Introduction 9
- X7SBA Image 9
- User’s Manual 10
- Important Notes to the User 10
- X7SBA Quick Reference 11
- Motherboard Features 12
- 1-2 Chipset Overview 15
- 1-3 PC Health Monitoring 16
- 1-5 ACPI Features 17
- 1-6 Power Supply 18
- Chapter 2 19
- Installation 19
- Installation Procedures 20
- Top View Of DDR2 Slot 25
- Front Control Panel 26
- Power LED 27
- NMI Button 27
- NIC1/NIC2 LED Indicators 28
- Overheat/Fan Fail LED (OH) 29
- Power Failure LED 29
- Power Button 30
- Reset Button 30
- 2-6 Connecting Cables 31
- Chassis Intrusion 32
- Overheat LED/Fan Failure 32
- Alarm Reset 33
- Universal Serial Bus (USB) 34
- GLAN (Giga-bit Ethernet 34
- ATX PS/2 Keyboard and 35
- Mouse Ports 35
- Speaker Connector 35
- Fan Headers 36
- . When using Thermal Manage 36
- Wake-On-Ring 37
- Wake-On-LAN 37
- VGA Connector 38
- SMB_PS (I 38
- C) Connector 38
- T-SGPIO Headers 39
- Power Fault (PWR Supply 39
- Failure) 39
- 2-7 Jumper Settings 40
- SMBus to PCI/PCI-Exp. Slots 41
- . The default setting is 41
- CMOS Clear 41
- Watch Dog Enable 42
- VGA Enable/Disable 42
- USB Wake-Up 43
- A. GLAN1 Port 44
- B. GLAN2 Port 44
- C. Onboard LED 44
- A. Floppy 45
- SIMSO IPMI 46
- Parallel Port Connector 46
- Chapter 3 47
- Troubleshooting 47
- User's Manual 48
- Memory Errors 48
- 4-1 Introduction 53
- 4-2 Running Setup 54
- 4-3 Main BIOS Setup 54
- Main BIOS Setup Menu 55
- 4-4 Advanced Setup 58
- Continue CR after POST 69
- Hardware Monitoring 69
- CPU Overheat Alarm 69
- Existing Event Log Number 73
- Event Log Control 73
- 4-5 Security Settings 76
- Fixed Disk Boot Sector 77
- Password on Boot 77
- 4-6 Boot Settings 78
- 4-7 Exit 79
- Appendix A 81
- POST Error Beep Codes 81
- X7SBA User's Manual 82
- Appendix B 83
- Installing the Windows OS 83
- Appendix C 85
Related products and manuals for Motherboards Supermicro X7SBA
Motherboards Supermicro C7P67 User Manual
(95 pages)
(95 pages)
Motherboards Supermicro X8DTH-6F User Manual
(101 pages)
(101 pages)
Motherboards Supermicro C7X58 User Manual
(101 pages)
(101 pages)
Motherboards Supermicro P4DP6 User's Guide
(103 pages)
(103 pages)
Motherboards Supermicro X7DCX User Manual
(91 pages)
(91 pages)
Motherboards Supermicro X7DVL-3 User Manual
(93 pages)
(93 pages)
Motherboards Supermicro X7DBI+ User Manual
(93 pages)
(93 pages)
© 2020, manymanuals.com. All rights reserved. | 1.345 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals