Supermicro X7DBE-X Datasheet Page 18
- Page / 130
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
1-12
X7DB8-X/X7DBE-X User's Manual
Main Switch Override Mechanism
When an ATX power supply is used, the power button can function as a system
suspend button to make the system enter a SoftOff state. The monitor will be
suspended and the hard drive will spin down. Pressing the power button again
will cause the whole system to wake-up. During the SoftOff state, the ATX power
supply provides power to keep the required circuitry in the system alive. In case
the system malfunctions and you want to turn off the power, just press and hold
the power button for 4 seconds. This option can be set in the Power section of
the BIOS Setup routine.
External Modem Ring-On
Wake-up events can be triggered by a device such as the external modem ringing
when the system is in the SoftOff state. Note that external modem ring-on can only
be used with an ATX 2.01 (or above) compliant power supply.
Wake-On-LAN (WOL)
Wake-On-LAN is defi ned as the ability of a management application to remotely
power up a computer that is powered off. Remote PC setup, up-dates and asset
tracking can occur after hours and on weekends so that daily LAN traffi c is kept to
a minimum and users are not interrupted. The motherboard has a 3-pin header
(WOL) to connect to the 3-pin header on a Network Interface Card (NIC) that has
WOL capability. In addition, an onboard LAN controller can also support WOL
without any connection to the WOL header. The 3-pin WOL header is to be used
with a LAN add-on card only.
*Note: Wake-On-LAN requires an ATX 2.01 (or above) compliant power supply.
1-6 Power Supply
As with all computer products, a stable power source is necessary for proper and
reliable operation. It is even more important for processors that have high CPU
clock rates.
The X7DB8-X/X7DBE-X can only accommodate 24-pin ATX power supplies. Al-
though most power supplies generally meet the specifi cations required by the CPU,
some are inadequate. In addition, the 12V 4-pin power supply - is also required to
ensure adequate power supply to the system. Also your power supply must supply
1.5A for the Ethernet ports.
- SUPER 1
- Preface 3
- Table of Contents 4
- Chapter 3: Troubleshooting 6
- Chapter 4: BIOS 6
- Appendices: 6
- Chapter 1 7
- Introduction 7
- Contacting Super Micro 8
- X7DB8/E-X 10
- J27, J28 I 11
- Motherboard Features 12
- 14
- 1-2 Chipset Overview 15
- 1-3 Special Features 16
- 1-4 PC Health Monitoring 16
- 1-5 ACPI Features 17
- 1-6 Power Supply 18
- 1-7 Super I/O 19
- Chapter 2 21
- Installation 21
- 2-3 Installing DIMMs 26
- Chapter 2: Installation 27
- DDR2 FBD Slot 27
- Back Panel Connectors 28
- B. Front Control Panel 29
- Power LED 30
- NMI Button 30
- NIC1/NIC2 LED Indicators 31
- Overheat/Fan Fail LED (OH) 32
- Power Fail LED 32
- Power Button 33
- Reset Button 33
- 2-5 Connecting Cables 34
- Universal Serial Bus (USB) 35
- Chassis Intrusion 35
- Fan Headers 36
- . Note: Default: 36
- ATX PS/2 Keyboard and 37
- PS/2 Mouse Ports 37
- Serial Ports 37
- Wake-On-Ring 38
- Wake-On-LAN 38
- Power LED/Speaker 39
- GLAN 1/2 (Giga-bit Ethernet 39
- Power Fault (PWR Supply 40
- Failure) 40
- Alarm Reset 40
- Overheat LED/Fan Fail 41
- Power SMB (I 42
- C) Connector 42
- VGA Connector 42
- SGPIO Headers 43
- 2-6 Jumper Settings 44
- CMOS Clear 45
- Watch Dog Enable/Disable 45
- SCSI Controller Enable/ 46
- Disable (*X7DB8-X Only) 46
- SCSI Termination Enable/ 46
- 3rd PWR Supply PWR Fault 47
- Detect (J3P) 47
- VGA Enable/Disable 47
- 2-7 Onboard Indicators 49
- Onboard SCSI Activity LED 50
- Indicators (*X7DB8-X only) 50
- Onboard Power LED 50
- and SCSI Connections 51
- SIMLP IPMI Slot 52
- IDE Connector 52
- Ultra 320 SCSI 53
- Connectors 53
- (*X7DB8-X only) 53
- Chapter 3 55
- Troubleshooting 55
- Memory Errors 56
- Chapter 4 59
- 4-2 Running Setup 60
- 4-3 Main BIOS Setup 60
- Main BIOS Setup Menu 61
- Port2 and SATA Port3 62
- 4-4 Advanced Setup 65
- Hardware Monitoring 76
- (*See the Note on Page 4-18.) 77
- CPU Temperature Threshold 77
- Voltage Monitoring 77
- Realtime Sensor Data 81
- 4-5 Security 82
- 4-6 Boot 83
- 4-7 Exit 84
- Appendix A 85
- BIOS POST Messages 85
- Appendix B 91
- BIOS POST Codes 91
- POST Code Description 92
- Appendix C 97
- The Intel Matrix Storage 98
- Creating a RAID 0 Volume: 100
- Creating a RAID 1 Volume: 101
- Deleting RAID Volume: 104
- with RAID Functions 106
- Managing Arrays 110
- Confi guring Disk Drives 111
- Creating Arrays 114
- Rebuilding Arrays 120
- Using the Disk Utilities 122
- Installing the OS 126
Related products and manuals for Motherboards Supermicro X7DBE-X
Motherboards Supermicro X6DAL-XG-B Datasheet
(108 pages)
(108 pages)
Motherboards Supermicro X10SLQ User Manual
(113 pages)
(113 pages)
Motherboards Supermicro X6DVL-EG2 User Manual
(106 pages)
(106 pages)
Motherboards Supermicro X6DVA-4G-B Datasheet
(82 pages)
(82 pages)
Motherboards Supermicro X6DHE-XG2-B User Manual
(110 pages)
(110 pages)
Motherboards Supermicro 370DLR User Manual
(106 pages)
(106 pages)
Motherboards Supermicro C2SBM-Q User Manual
(95 pages)
(95 pages)
Motherboards Supermicro X6DHI-G2-B User Manual
(120 pages)
(120 pages)
Motherboards Supermicro C2G41 User Manual
(93 pages)
(93 pages)
Motherboards Supermicro H8DCR-I User Manual
(78 pages)
(78 pages)
Motherboards Supermicro X7DAE User Manual
(133 pages)
(133 pages)
Motherboards Supermicro PDSMA User Manual
(101 pages)
(101 pages)
Motherboards Supermicro P4SGA+ User Manual
(93 pages)
(93 pages)
© 2020, manymanuals.com. All rights reserved. | 0.127 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals